How to Make a Permanent Magnet Piston

Authored or posted by | Updated on | Published on March 8, 2017 | Reply
Share Button

Picture of a Magnet Piston Prototype

If created properly, an engine built with permanent magnet pistons is much more efficient than a traditional piston engine. This type of engine may even be able to generate more energy than it consumes. An engine that can do this is known as an overunity engine.

From YouTube.com:

The Parts list is below and at the end of the video. This video will show you how to make a permanent magnet piston that can physically amplify an input force by a factor of 3.33 x It easily proves every single thing I say and claim. It would make a great science experiment for any science class.

PARTS LIST:

http://www.petmountain.com/show_product/11442-504991
Lee’s LEES RIGID TUBING 3/16″ X 3FT
Item # SPM6960490304 Model # 16005

(Must enlarge the center of this tubing with a 9/64″ drill bit and glued into 7/8″ magnets)

http://www.amazon.com/
Solid Brass Rod 36″,1/8″ (5) (I cut them in half to 18″)
by K&S Engineering
ASIN: B0006MZUL6

http://www.magnets-4-less.com/
Neodymium Magnets

7/8 in x 7/8 in with 3/16 in Hole Rare Earth Ring Model#[NR012] (need 3 of these)

N48 3/4 in OD x 1/4 in ID x 3/4 in Rare Earth Ring Model#[NR011-1] (need 1 of these)

(may want to buy several in case you crack them or want to make more than 1 piston)

http://www.usplastic.com/

58061 1/8″ ID x 1/4″ OD x 1/16″ Wall Superthane® Ether Based Tubing (glue into ¾” magnet)

44029 1″ OD x 7/8″ ID Acrylic Tubing ( 7/8″ magnets are glued into this tubing, cut into about 10″ pieces)

34104 1″ Clear Rigid PVC Pipe (44029 tubing will slide in and out of this tubing easily)

44033 1 1/2″ OD x 1 1/4″ ID Acrylic Tubing (Must be sanded for a good fit)

44034 1 3/4″ OD x 1 1/2″ ID Acrylic Tubing (Must be sanded for a good fit)

44035 2″ OD x 1 3/4″ ID Acrylic Tubing (Must be sanded for a good fit)

45084 1/16″ x 24″ x 48″ Gray PVC Sheet (cut about a 3″ x 4″ piece off for base)

Other items needed:

9/64″ drill bit, Sandpaper, Grinder bit, Superglue, Hot glue for base ring.

This is made out of plastic and glue … it is for demonstration and experimental testing purposes only. They will not last that long. Use caution when handling magnets.

How to make a Permanent Magnet Piston

The Permanent Magnet Piston: Energy for the Future

Check out this forum for more information on magnet piston.

Share Button


Donate to Help Make a Difference

EnergyFanatics.com is a true independent blog because it is not financed and controlled by banksters. If you like reading the articles on this site, please take action now by clicking the "Donate" button below to send a donation to the author/editor. Your generous support will help fund his research and expenses, allowing him to continue his quest to educate and teach people to create a better world for everyone.


Category: Free & Alternative Energy

Leave a Reply

Comment Policy: Please keep comment relevant to the content of the article. Profanity, spamming and use of threatening language will not be tolerated. Links are allowed but please do not spam the comment section with excessive links. Dead, inappropriate, excessive or advertising links will be removed. I reserve the right to edit or delete any comments that I feel are inappropriate.